|
|
|
Our T16-002 interface
has a male pin OBD2 connector on one end and a female pin DB9 on the
other and is also opto-isolated. You can connect it to your PC
using a straight through RS232 cable.
For most applications we do
recommend the T16-013 instead of the T16-002 because the opto-isolation is
not needed for most applications. Our T16-002 and T16-013 both support
J1850 VPW, J1850 PWM, ISO-9141-2 and ISO-14230 (KWP2000). |
T16-002, $82 each |
|
|
|
|
|
T16-003,
$82 each |
This interface has a
male pin OBD2 connector on one end and a male pin DB9 connector on the other.
You will need a null modem cable to connect the interface to your computer. It
will work fine with most Palm hotsync cables. A few Palm devices have unusual
RS232 and do not work properly. Our T16-003 supports J1850 VPW, J1850 PWM,
ISO-9141-2 and ISO-14230 (KWP2000) |
|
|
|
|
|
|
Same as our T16-003 without the connectors and enclosure.
This is a circuit card assembly only. You will need a null modem cable to
connect the interface to your computer. Our T16-004 supports J1850 VPW,
J1850 PWM, ISO-9141-2 and ISO-14230 (KWP2000).
|
T16-004,
$69.50 each |
|
|
|
|
|
T16-005,
69.50 each |
Same as our T16-006 without the connectors and enclosure. This is a
circuit card assembly only. You will need a cable 16 to connect the
interface to your vehicle. Our T16-005 supports J1850 VPW, J1850 PWM,
ISO-9141-2 and ISO-14230 (KWP2000).
|
|
|
|
|
|
Our T16-006 interface
has a female pin DB9 connector on the OBD2 end and a male pin DB9
connector on the other. You will need a cable 16
to connect the interface
to your vehicle. Our T16-006 supports J1850 VPW, J1850 PWM, ISO-9141-2
and ISO-14230 (KWP2000) |
T16-006,
$82 each |
|
|
|
|
|
T16-007,
$82 each |
A CAN
only interface with a female DB9 connector on each end. You can connect
it to your computer using a null modem cable. The T16-007 supports J1850 VPW, J1850 PWM,
ISO-9141-2 and ISO-14230 (KWP2000) |
|
|
|
|
|
|
Our
T16-008 interface has a female pin DB9 connector on the OBD2 end and a
male pin DB9 connector on the other. You will need a cable 16 to connect
the interface to your vehicle. Our Cable 16 is a 4 foot long cable with a
male pin DB9 connector on the interfacing end and a male pin OBD2
connector to the vehicle end. They cost $22.50 each. Our T16-008
supports J1850 VPW, J1850 PWM, ISO-9141-2 and ISO-14230 (KWP2000)
and CAN for $122.00 each. This is basically a T16-006 with CAN
capabilities |
T16-008,
$122 each |
|
|
|
|
|
T16-009,
$122 each |
This interface
has a male pin OBD2 connector on one end and a male pin DB9 connector on
the other. You can connect it to your Palm Pilot using a hotsync
Cable. Our T16-009 supports J1850 VPW, J1850 PWM, ISO-9141-2
and ISO-14230 (KWP2000) and CAN. This is basically a T16-003 with
CAN capabilities.
|
|
|
|
|
|
Our T16-010 interface is a CAN only interface.
This is a board only with a DB9 on each end.
|
T16-010,
$69.50 each,
|
|
|
|
|
|
|
T16-011,
$122.00 each.
|
The
T16-011 is our T16-002 with CAN capabilities.
It has a
male pin OBD2 connector on one end and a female pin DB9 on the other. Our
T16-011 is also opto-isolated. You can connect it to your PC using a
straight through RS232 cable.
|
|
|
|
|
|
|
CAN only interface with an
OBD2 connector built on one end.
You can use a null modem cable to connect to your computer.
|
T16-012 ,
$82 each
|
|
|
|
|
|
|
.jpg)
T16-013,
$82 each |
This interface
has a male pin OBD2 connector on one end and a female pin DB9 connector on
the other end. You can connect the interface to your computer using a
straight through RS232 cable. Our T16-013 supports J1850 VPW, J1850 PWM,
ISO-9141-2 and ISO-14230 (KWP2000).
|
|
|
|
|
|
|
This interface
has a male OBD2 connector on one end and a female DB9
connector on the other. You can connect the interface to your computer
using a straight through RS232 cable. Our T16-014 supports J1850 VPW,
J1850 PWM, ISO-9141-2 and ISO-14230 (KWP2000) and CAN
This is a T16-013 with CAN capabilities. |
T16-014,
$122. each |
|
|
|
|
|
|
T21-002,
$118 each |
OBD2
Interface for J1850 VPW/PWM, ISO9141-2, ISO14230 (KWP), ISO15765 (CAN) to USB.
Captive 8 foot long USB cable and a built-in OBD2 Connector.
|
|
|
|
|
|
OBD2 Interface for J1850 VPW/PWM, ISO9141-2,
ISO14230,ISO15765 TO USB, requires DB9 to OBD2 CABLE |
T21-003,
$118 each |
|
|
|
|
T22-001 OBD2 INTERFACE TESTER
$144.00 each |
Our interface tester is used to fully test
all protocols used in OBD2 communications to verify that all parts of an
OBD2 test station are functional prior to performing any testing on a car.
The test can be accomplished in about two (2) seconds.
We offer the T22 with a built-in female
OBD2 connector. It is also available with a DB9 for use with a DB9
female OBD2 cable. The use of a replaceable cable is recommended for
applications where the T22 will be connected to an OBD2 interface many
times during any period of time.
Currently the T22 is used to test
our interfaces only. However with proper software it is
possible it could be used to test other OBD2 interfaces.
|
|
|
|
This version of the OBD2 interface tester is intended for
use with a detachable cable. It was designed for applications that
require a lot of testing. The use of the detachable cable allows
replacement of the female OBD2 connector when it wears out. This
version is recommended for I/M inspection stations.
|
T22-002 OBD2 INTERFACE
TESTER
$122 each
|
